The author is making a number of good annotation on A Step-by-Step Guide to Installing a Bathtub as a whole in this article further down.
Installing a tub isn't precisely brain surgery, however it does need strong plumbing, woodworking, and also occasionally, tiling skills. Replacing an old tub with a new one is also a moderately challenging project. If the old tub is readily available, the job can move quickly; if you have to open a wall to remove the old tub and place the new bath tub, the task is much harder. In either instance, the task is within a house handyman's skills, although you will require an assistant to leave the old tub and also embeded in the new one. Ensure you have actually certified on your own for the job as well as are comfortable trying it. Rather than employing a professional to take over a halfway-completed task, it is much better to take into consideration utilizing one before you start. Possibilities are you may require an expert plumber to make tube connections.
This article will aid you set up a new bathtub in your shower room if you have currently purchased a brand-new bathtub and do not need to change the plan of your previous supply of water pipelines.
Your devices and product list must comprise the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you should do is detach the water supply. After doing so, switch on the taps to drain pipes any water staying in the system. The procedure of eliminating the existing faucets can be rather bothersome because of the limited access that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will certainly come from the pipes. As soon as the supply pipes have actually been gotten rid of, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new faucets to fit.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and also the other end offers a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, place the faucet in the placing hole in the bath/basin ensuring that the washers are in place between the tap as well as the sink. Protect the faucet in position with the manufacturer provided backnut. Once the tap is safely in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The previous kind should be connected to the tap ends first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Installing the Tub
Utilizing both wood boards under its feet, position the bathtub in the required placement. The wood boards are helpful in evenly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the tub up until the level reviews degree.
To mount faucets, fit all-time low of the outermost versatile faucet port to the suitable supply pipe by making a compression join; then do the exact same for the other tap.
Switch on the water supply and check all joints and brand-new pipework for leakages and also tighten them if essential. Fill the bath tub as well as likewise check the overflow outlet and also the regular outlet for leaks.
Ultimately, take care of the bath paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the bath tub should wait till the tub has been used at the very least once as this will resolve it right into its final placement.
Getting ready for the Setup
To start with, the sustaining frame supplied with the bath needs to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps system to prevent pressure on the bathtub.
Fit the adaptable tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its final placement.
Tiling Around the Bathtub
In the area where the bathroom meets the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break an inflexible seal, causing the water to permeate the wall surface between the bath and also the tiling, leading to complications with dampness and feasible leakages to the ceiling below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as installations. They are marketed in tubes and cartridges, and are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water before sealing, to allow for the movement experienced when the tub is in use. The sealant can break relatively early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise quickly readily available on the marketplace. It is suggested to fit the tiles using water-resistant or waterproof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our part about How to Install a Bathtub Yourself. Thanks for taking the time to read through our piece. Appreciated our blog posting? Please share it. Help someone else locate it. Thank-you for going through it.
Visit Our Site